300A Electrical Cabinet Power Distribution Panel Board

300A electrical cabinet power distribution panel board

 

 

 

After years of development, the switchgear mainly consists of two parts: the cabinet body and the circuit breaker, with functions such as overhead incoming and outgoing lines, cable incoming and outgoing lines, and busbar connection.

The cabinet body is composed of a shell, electrical components (including insulation parts), various mechanisms, secondary terminals, and wiring.

Cabinet material:

1) Cold rolled steel plate or angle steel (used for welding cabinets).

2) Aluminum zinc coated steel plate or galvanized steel plate (used for assembling cabinets).

3) Stainless steel plate (non magnetic).

4) Aluminum plate (non magnetic).

Functional units of the cabinet:

1) The main busbar room (usually arranged in two structures: "pin" or "1")

2) Circuit breaker room

3) Cable room

4) Relay and instrument room

5) Cabinet top small busbar room

6) Secondary terminal compartment

 

Electrical components inside the cabinet:

1. The common primary electrical components (main circuit equipment) inside the cabinet include the following equipment:

Current transformer abbreviated as CT [e.g. LZZBJ9-10]

Voltage transformer abbreviated as PT [e.g. JDZJ-10]

Grounding switch [e.g. JN15-12]

Lightning arrester (resistance capacitance absorber) [such as HY5WS single-phase type; TBP, JBP combination type]

Isolation switch [such as GN19-12, GN30-12, GN25-12]

High voltage circuit breakers [such as: low oil type (S), vacuum type (Z), SF6 type (L)]

High voltage contactor [such as JCZ3-10D/400A type]

High voltage fuses [such as RN2-12, XRNP-12, RN1-12]

Transformers [such as SC (L) series dry transformers and S series oil transformers]

High voltage live display 【 GSN-10Q type 】

 

Insulating components [such as wall bushings, contact boxes, insulators, insulation heat shrink (cold shrink) sheaths]

Main busbar and branch busbar

High voltage reactor [such as series type: CKSC and starter motor type: QKSG]

Load switch [such as FN26-12 (L), FN16-12 (Z)]

High voltage single-phase parallel capacitors [such as BFF12-30-1], etc

2. The main secondary elements commonly used in the cabinet (also called secondary equipment or auxiliary equipment, which refers to low-voltage equipment for monitoring, controlling, measuring, adjusting and protecting the primary equipment) are as follows:

1. Relay 2. Energy meter 3. Ammeter 4. voltmeter 5. Power meter 6. Power factor meter 7. Frequency meter 8. Fuse 9. Air switch 10. Transfer switch 11. Signal light 12. Resistance 13. Buttons 14. Microcomputer integrated protection device, etc.

 

2、 Classification of high-voltage switchgear

1. According to the installation method of circuit breakers, they are divided into movable (handcart) and fixed types

(1) Mobile or handcart (represented by Y): Indicates that the main electrical components inside the cabinet (such as circuit breakers) are installed on withdrawable handcart. Due to the excellent interchangeability of handcart cabinets, it can greatly improve the reliability of power supply. Commonly used handcart types include: isolation handcart, metering handcart, circuit breaker handcart, PT handcart, capacitor handcart, and used variable handcart, such as KYN28A-12.

(2) Fixed type (represented by G): indicates that all electrical components inside the cabinet (such as circuit breakers or load switches) are installed in a fixed type. Fixed type switchgear is relatively simple and economical, such as XGN2-10, GG-1A, etc.

2. Divided into indoor and outdoor according to installation location

(1) Used indoors (represented by N); Indicates that it can only be installed and used indoors, such as KYN28A-12 switch cabinets;

(2) For outdoor use (indicated by W); Indicating that it can be installed and used outdoors, such as XLW switchgear.

3. According to the cabinet structure, it can be divided into four categories: metal enclosed armored switchgear, metal enclosed interval switchgear, metal enclosed box switchgear, and open switchgear:

 

(1) The main components of metal enclosed armored switchgear (represented by the letter K), such as circuit breakers, transformers, busbars, etc., are respectively installed in grounded metal partitions separated by metal enclosed switchgear. For example, KYN28A-12 high-voltage switchgear.

(2) Metal enclosed bay switchgear (represented by the letter J) is similar to armored metal enclosed switchgear in that its main electrical components are also installed in separate compartments, but have one or more non-metallic partitions that meet a certain level of protection. For example, JYN2-12 high-voltage switchgear.

(3) Metal enclosed box type switchgear (represented by the letter X) The switchgear enclosure is a metal enclosed switchgear. For example, XGN2-12 high-voltage switchgear.

(4) Open type switchgear, without protection level requirements, with some parts of the casing being open switchgear. For example, GG-1A (F) high-voltage switchgear

 

Service Conditions:

◎ Ambient airtemperature: -15°C~+40°C;

 

◎ Relative humidity: Daily average 95%，and daily average of water vapor pressure < 2.2kPa;

◎ Monthly average «90%, and monthly verage of water vapor pressure < 1.8kPa;

© Altitude: ^1000m;

◎ Seismic intensity: not beyond Ms8.

◎ Ambient air should be free of pollution of corrosive or flammable gas or vapor;

◎ No obvious vibration;

Main technical parameters
Rated voltage	.....................................	kV	3.6、7.2、12
Rated frequency	.....................................	Hz	50
Rated current of circuit breaker	.....................................	A	630/4000
Rated current of switchgear	.....................................	A	630/4000
Rated short-time withstand current (4S)	.....................................	kA	20、25、31.5、40
Rated peak withstand current (peak)	.....................................	kA	50、63、80、100
Rated short-circuit breaking current	.....................................	kA	20、25、31.5、40
Rated insulation level 1min power frequency withstand voltage	Pole-to-pole, pole-to- ground	kV	24、32、42
	Between open contacts	kV	24、32、48
Lightning impulse withstand voltage (peak)	Pole-to-pole, pole-to- ground	kV	40、60、75
	Between open contacts	kV	46、70、85
The shell is IP4X, and it is IP2X when the compartment door and circuit breaker chamber door are opened

 

Features

1: STRICT protection step to ensure personal safety

 

2: The cable room can be installed as many as 9 single-core cables

 

3: Operation and testing positions will be established for the handcart, and both positions are equipped with safe and reliable positioning device and display device

 

4: The enclosure is completely assembled from aluminized and galvanized steel plate, which are machined and bent by machine tool and then bolted.

 

5: It has high mechanical strength and its neatness and beauty is ensured.

 

6: The switchboard door is sprayed with plastic, also has strong capacity of impact resistance and corrosion protection.

 

7: The primary switch may be provided with VD4 vacuum circuit breaker and C3 series of fixed type load switch from ABB, various domestic vacuum circuit breakers (such as VS1, VH1, VK, ZN28) may also be provided in lieu of the same foreign products.

 

8: Front door is installed with a observation window to check the operating state of the components inside the room

 

 

Q5 : Is OEM/ODM available?

A: Yes, it is! Our products can be Customized. We have design and engineer teams,we can customize products according to customers' drawing or requirements.

 

Q6 : You are manufacturer or trading company?
A: We are factory, As a 100% professional manufacturer with 20 year's manufacturer experience, we could produce products according to customers' requirements and we could also control the quality of products 100%.

 

Q7 : Can the price be negotiated?

A: Yes, the price is negotiable. It can be changed according to your quantity or package

 

Q8 : How about inspection?

A: We have the whole inspection system from raw material to end products include temperature rise test,salt spraying test conductor type test,mechanical life test.

 

Q9 : What is payment terms?

A: T.T, Paypal,Western Union,Alibaba trade assurance and L/C is acceptable. 30% T/T in advance ,70% balance before shipment.

 

Q10 : What is the service offered by company?

A: We have the professional engineer team which can design and develop the mold to arrive different customer requirement.

We also have the sales team to offer good service from pre-sale to after-sale.

 

This product is usually customized.
We are a manufacturer and have a professional technical department that can design and provide solutions according to customer needs.
Please contact our sales personnel to obtain design drawings

Here are our customer examples for your reference

 

IF NEED MORE DETAILES,PLEASE FEEL FREE YO CONTACT US

Hot Tags: 300a electrical cabinet power distribution panel board, China, manufacturers, suppliers, customized